Two independent reviews of the XGIMI HORIZON 30 Ultra Max have now published full lab numbers, and on brightness they are more than 1,300 lumens apart. German site Netzwelt measured 4,440 lumens in its most accurate picture mode. Belgian reviewer Laurent Willen, whose test went up on November 8, measured 3,126 lumens in Filmmaker mode on the same model. The gap was first lined up side by side by Prad.de on November 15. It lands the day before XGIMI’s Black Friday sale cuts the projector from $3,499 to $2,999 in the US.
XGIMI rates the Ultra Max at 6,000 ISO lumens, the highest figure in the HORIZON 30 range. In its brightest mode Netzwelt got 5,770 lumens, 3.8 percent short of the claim. Willen’s brightest reading was 3,878 lumens in the Bright preset, with the laser at its top level and the iris at step 2. That puts the two tests 1,892 lumens apart at full output and 1,314 lumens apart once the colours are set correctly.
Almost everywhere else, the numbers line up. With the iris fully open, Netzwelt measured contrast at just under 1,500:1. Willen got 1,330:1 to 1,482:1, depending on laser level. Closing the iris to step 4 raised contrast to about 2,600:1 at Netzwelt and 2,516:1 to 2,833:1 at Willen’s. Both tests kept roughly 76 percent of the light at that setting: about 3,400 lumens at Netzwelt, and 3,256 down to 2,480 lumens in Standard mode for Willen. XGIMI’s own spec sheet claims 10,000:1 native contrast. Neither test came close to that.
Power draw is nearly identical, at 186 watts for Netzwelt and 185 watts for Willen, against a spec-sheet figure of up to 300 watts. Willen saw 101 watts at the lowest laser level, and Netzwelt measured 0.5 watts in standby. Both put fan noise at 28 dB(A), which is XGIMI’s own figure. Both also heard a hum. Willen’s C-weighted reading, which picks up low-frequency sound, rose from 35.7 dB with the projector off to 37.9 dB with it running. He thinks the XPR pixel-shifting is the cause and says he has reported it to XGIMI. He doesn’t consider it a deal-breaker.
Only Willen published colour figures. In Filmmaker mode his average Delta E was 2.50 to 2.73 with SDR, depending on iris setting, and 3.3 to 3.9 with HDR. That is very good for a projector straight out of the box. One caveat is the white point. It drifts once the iris closes past step 4, with SDR white Delta E rising from 4.49 at step 4 to 6.56 at step 5. At step 5 he measured 3,673:1 at 1,632 lumens, and the dynamic black-level mode pushed contrast past 50,000:1. Even then, the black level was below his meter’s 0.01 cd/m² floor, so that number is a lower bound.
Only Netzwelt measured input lag: 13 ms at 60Hz and under 8 ms in the Boost gaming mode. As we noted when we covered the Netzwelt review last week, 4K at 120Hz only works once the HDMI-EDID setting in the menu is switched from HDMI 2.0 to HDMI 2.1. On the default setting, a console is limited to 60Hz at 4K or Full HD.
Neither review explains the gap, and Willen says plainly that his method doesn’t measure the same thing as the manufacturer’s rating. XGIMI’s 6,000 figure is ISO 21118 output, measured as light flux over a grid of points on the screen. Willen measures luminance on the screen from the seating position and works out light output from that. Screen gain, image size and where the meter sits all affect the result. A tester using this method will usually come in below a flux reading, though not always by this much.
Firmware is the other variable. Willen tested four XGIMI projectors over several weeks, ran at least two firmware versions on each, and says his conclusions are based on version 0.7.26. He describes that as close to, but not, the final release. Netzwelt’s unit came on loan from XGIMI and was tested a week later. Laser drive levels are set in software, so a firmware change could plausibly move peak output by hundreds of lumens. Neither site has said which build Netzwelt used, so this is a possible explanation, not a confirmed one.
The practical takeaway for a buyer is that both readings are high for a living-room projector. Either 3,126 or 4,440 calibrated lumens will fill a 120-inch screen in a room with some lamps on. What the gap does undermine is spec-sheet shopping. The difference between the Ultra Max and the cheaper HORIZON 30 Pro, rated at 4,800 ISO lumens, is smaller in Willen’s test than the gap between the two reviews themselves. Willen makes the same point in his own write-up: unless you need a lot of brightness, he says, the Pro is more than enough.
XGIMI’s US store listed the Ultra Max at $3,499 on November 18, with the floor-stand bundle at the same price and the ceiling-mount bundle unavailable. From November 19 to 30, XGIMI’s Black Friday pricing takes it to $2,999 and the HORIZON 30 Pro to $1,899. That makes the step up $1,100 for a projector that, on Willen’s numbers, has less of a brightness lead over the Pro than its rating suggests. In Germany the recommended price is €3,299, and XGIMI’s European stores list it at that price, as do Amazon France and Amazon Germany.
The closest rival is still the JMGO IRIS Ultra Max, $3,299 on JMGO’s global store. Netzwelt measured it at 4,350 lumens in cinema mode and up to 8,600:1 contrast with the iris stopped down. For a dark room, that contrast difference matters more than any lumen figure in this story. Our HORIZON 30 Ultra Max product page has the full spec sheet, and the home theater projector guide covers what we would put in a light-controlled room.
Whether the 1,300 lumens are a measuring difference or a firmware difference should be clear soon. Willen has said he is waiting for a new firmware release to see whether the hum improves. A brightness reading on that build would settle the question. If his number moves toward 4,400, the early firmware was the reason. If it doesn’t, the most useful brightness figure for this projector is the range between the two tests, not 6,000.